The Fundamentals of Plumbing Knowledge When Installing a Bathtub
The Fundamentals of Plumbing Knowledge When Installing a Bathtub
Blog Article
What're your concepts on How to Install a Bathtub Yourself?
Installing a tub isn't exactly rocket science, however it does need solid plumbing, carpentry, as well as sometimes, tiling skills. Changing an old bath tub with a brand-new one is additionally a reasonably tough project. If the old tub is conveniently obtainable, the job can move easily; if you have to open up a wall to get rid of the old tub as well as place the new bathtub, the task is much harder. In either instance, the project is within a house handyman's abilities, although you will certainly need a helper to vacate the old tub and set in the brand-new one. Ensure you have actually certified on your own for the job as well as fit trying it. Rather than employing a contractor to take over a halfway-completed project, it is much better to take into consideration using one prior to you start. Opportunities are you might require a specialist plumber to make tube links.
This post will certainly assist you set up a new bathtub in your bathroom if you have already acquired a brand-new bathtub and do not need to alter the setup of your previous water system pipelines.
Your devices and product list ought to consist of the following:
Planning for the Installation
Firstly, the sustaining frame provided with the bath should be fitted (if called for) according to the maker's instructions. Next, fit the faucets or mixer to the tub. When suitable the tap block, it is necessary to ensure that if the tap comes with a plastic washing machine, it is fitted in between the bath and the faucets. On a plastic bathroom, it is also practical to fit a sustaining plate under the taps system to avoid strain on the bathtub.
Fit the versatile faucet adapters to the bottom of both faucets making use of 2 nuts and olives (in some cases supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and then pass the electrical outlet via the hole in the bathroom. Utilize the nut supplied by the producer to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the versatile overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bath. Ensure you utilize all of the supplied washers.
Attach the trap to the bottom of the waste outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Attach all-time low of the overflow tube in a similar manner.The bathroom should now be ready to be fitted in its last placement.
Removing Old Touches
If you require to change old taps with new ones as a part of your installation, then the first thing you should do is separate the water. After doing so, activate the taps to drain any kind of water continuing to be in the system. The procedure of getting rid of the existing taps can be quite troublesome because of the limited accessibility that is frequently the situation.
Make use of a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that links the supply pipelines to the taps. Have a cloth all set for the remaining water that will certainly originate from the pipes. As soon as the supply pipes have actually been gotten rid of, use the same tool to loosen up the nut that holds the faucets onto the bath/basin. You will certainly need to stop the single faucets from transforming throughout this process. As soon as the taps have been gotten rid of, the holes in the bath/basin will certainly have to be cleaned up of any type of old sealing compound.
Before proceeding to fit the brand-new faucets, contrast the pipe connections on the old taps to the brand-new faucets. If the old faucets are longer than the brand-new faucets, then a shank adapter is needed for the new taps to fit.
Setting up the Tub
Making use of both wood boards under its feet, place the tub in the needed setting. The wooden boards are useful in evenly spreading out the weight of the bath tub over the location of the boards as opposed to concentrating all the weight onto 4 small factors.
The next goal is to make certain that the bath tub is leveled all round. This can be accomplished by inspecting the spirit level as well as changing the feet on the bathtub up until the spirit level reviews degree.
To install faucets, fit the bottom of the outermost adaptable tap port to the suitable supply pipe by making a compression sign up with; after that do the same for the various other faucet.
Switch on the water supply as well as examine all joints and new pipework for leakages and tighten them if essential. Fill the bathtub and also check the overflow outlet and the typical electrical outlet for leaks.
Ultimately, deal with the bathroom paneling as explained in the maker's instruction manual. Tiling and securing around the bath tub ought to wait until the bath tub has actually been used at least when as this will settle it right into its final setting.
Suitable New Taps
If the tails of the brand-new taps are plastic, then you will certainly need a plastic port to stop damages to the string. One end of the adapter fits on the plastic tail of the tap as well as the various other end supplies a connection to the existing supply pipelines.
If you need to fit a monobloc, then you will call for minimizing couplers, which connects the 10mm pipeline of the monobloc to the conventional 15mm supply pipeline.
Next, place the faucet in the mounting opening in the bath/basin making sure that the washers are in location in between the faucet and the sink. Safeguard the faucet in position with the manufacturer provided backnut. Once the tap is securely in place, the supply pipelines can be attached to the tails of the faucets. The faucets can either be linked by using corrugated copper piping or with normal faucet adapters. The previous type should be connected to the faucet finishes first, tightening only by hand. The supply pipes can later be connected to the other end. Tighten both ends with a spanner after both ends have actually been connected.
Tiling Around the Bath tub
In the area where the bathroom meets the floor tile, it is required to secure the joins with a silicone rubber caulking. This is necessary as the fitting can move enough to fracture a stiff seal, creating the water to permeate the wall between the bathroom and the tiling, leading to difficulties with moisture and also possible leakages to the ceiling below.
You can select from a selection of coloured sealants to blend in your fixtures and also fittings. They are offered in tubes as well as cartridges, and also can securing voids up to a width of 3mm (1/8 inch). If you have a larger gap to fill, you can fill it with twists of soaked newspaper or soft rope. Remember to always fill the tub with water before sealing, to allow for the motion experienced when the bathtub remains in use. The sealant can fracture relatively early if you do not consider this movement before sealing.
Additionally, ceramic coving or quadrant floor tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are also easily offered on the market. It is a good idea to fit the floor tiles making use of waterproof or water resistant adhesive as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I came across that blog post on How to Install a Bathtub when doing a lookup on the web. Sharing is nice. Helping people is fun. Thanks for your time. Don't hesitate to visit our blog back soon.
Damage control? Call us. Report this page